New windows and doors improve comfort, cut energy bills and add long-term value to your home. Meridian Windows and Doors Fresno pairs proven product lines with our own installing crews for lasting performance - and a price we put in writing.
Choose your installer
The unit is half the job - the install is the other half. Our own background-checked crews measure, set, seal and insulate every opening, and they know the lines we quote inside and out because they install them every week.
Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line homeowners arrive naming - the most impact certifications in the industry$$$
- More impact certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe value pick$$
- Vinyl systems built to strict wind codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Factory-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven inventory lines with short lead times
Awning & Hopper Windows in Fresno, CA
Awning windows hinge at the top and open outward from the bottom, while hopper windows hinge at the bottom and open inward from the top. Both work exceptionally well in Fresno’s climate because they seal tighter than sliding windows when closed and can stay open during light rain without letting water in. Meridian Windows and Doors Fresno installs and replaces both styles, drawn from our eight manufacturer lines so the window spec matches the opening and the exposure, not whatever happens to be sitting in a warehouse. Call (559) 272-4716 for a written estimate on any awning or hopper window project, or read more about our full Window Installation in Fresno service.
We work with homeowners across Fresno, from Fig Garden to Clovis West to Tower District, and the question we hear most often is whether these window styles actually work in a house that sees 100-degree days for months at a stretch. The answer: yes, if they’re specified correctly. Awning windows placed high on a wall let hot air escape while keeping sun off the glass below. Hopper windows in a laundry room or basement wall pull cool air in at the lowest point. Both depend on proper flashing and a square rough opening, which is where our crew’s discipline matters more than the brand name on the glass.
Key Takeaways
- Awning and hopper windows typically run $380 to $1,100 installed in Fresno, depending on size, frame material, and glass package.
- Both styles seal tighter than sliders and can vent during light rain, which suits the Valley’s seasonal downpours.
- Every Meridian Windows and Doors Fresno job gets a written price before work starts and a 365-Day Done Right Promise in writing.
- We stock and install from eight manufacturer lines, including PGT, ViewLux, and CGI, so the right product is spec’d per opening.
- Calls are answered by a live person, 24/7, including weekends and holidays.
When You Need Awning & Hopper Windows
Most Fresno homeowners don’t start out thinking about awning or hopper windows specifically. They start with a problem. Here are the situations we see in homes across Fresno and the surrounding neighborhoods, from Woodward Park to Sunnyside:
- Kitchen windows above a counter or sink. A slider over a counter is awkward to reach across, and a double-hung over a sink means leaning over the faucet to open it. An awning window with a crank or pole operator opens outward without you reaching over anything. In central Fresno kitchens built in the 1960s and 1970s, this is one of the most common replacements we do.
- Bathroom windows that fog or mildew around the sill. Bathrooms trap moisture, and a slider with a worn seal lets that damp air condense inside the track. A hopper or awning window with a compression seal closes tighter than a slider ever can, and when it’s open, it vents steam up and out. We see this constantly in older homes in the Tower District where the original wood sashes have swollen and the homeowners are tired of fighting them.
- Basement or utility room windows at or below grade. Fresno has more basements than people assume, especially in older homes near downtown and in the Huntington Boulevard corridor. Hopper windows are the standard solution here because they sit low, open inward, and fit into the smaller rough openings those homes were framed for.
- You want ventilation without giving up security. An awning window opened 4 inches still presents a barrier to anyone trying to climb through from outside. A slider opened 4 inches is an invitation. This matters for ground-floor bedrooms and home offices. ViewLux and PGT both make awning windows with multipoint locking hardware that engages at multiple points along the frame.
- Your current windows leak air so badly the room never holds temperature. In a Valley summer, a leaky window frame means your AC runs nonstop and the room still feels 10 degrees warmer than the hallway. Awning windows seal on all four sides when closed, with compression weatherstripping that actually presses the sash into the frame. That’s a physical seal, not just an overlap.
- You need a window in a hard-to-reach spot. Clerestory windows, windows above a stair landing, windows behind a soaking tub. You can’t safely lean over a bathtub to wrestle a double-hung open. An awning window with a gear-driven crank or a motorized operator solves it. We spec these regularly in custom builds in northeast Fresno.
If any of these sound like your house, the fix is straightforward. One phone call to (559) 272-4716, one visit from a technician who measures everything, and a written price before any work is scheduled.
Our Awning & Hopper Windows Process
The process is simple because we refuse to make it complicated. Here’s exactly how it goes when you call Meridian Windows and Doors Fresno:
- You call, a person answers. Not a voicemail tree. Not a callback service. A live person picks up at (559) 272-4716, takes your address and the scope of the problem, and schedules a visit. You’ll know who’s coming and when before you hang up.
- A uniformed, background-checked technician visits and measures. They check the rough opening dimensions, the condition of the existing frame and flashing, the exposure the window gets, and the condition of the surrounding stucco or siding. They’ll also note any water damage or dry rot at the sill, which is common in Fresno homes with older aluminum-frame windows.
- You get a written price on the spot. The price includes the window, the installation labor, the flashing, the interior and exterior trim as needed, and disposal of the old unit. It goes on paper before any deposit is collected, and it does not change at the door. No add-ons, no “we found rot” markup later.
- We order the right window from one of our eight lines. Depending on the opening, the exposure, and your budget, that might be a ViewLux awning with low-E glass for a west-facing wall, a PGT hopper with impact-rated glass for a ground-level bathroom, or a CGI unit if you want the strongest frame available. We don’t push one brand; we spec what the job needs.
- Installation day runs on a schedule. The crew arrives when we said they would, in uniform, with the area tarped and the old window out and the new one in with minimal dust. Most single awning or hopper window replacements take half a day. Multiple units usually finish in a day or two.
- You get the 365-Day Done Right Promise in writing. If anything about the installation fails within a year, we come back and fix it at no charge. No fine print about labor exclusions. The second visit is free, full stop. That’s the Garrison Standard, and it’s how this company has operated since 2009.
A meridian is a fixed line you measure everything against. That’s what the name means, and that’s how we run every install: measure against the standard, every time, no exceptions. This page is part of our broader window installation in Fresno work, and the same process applies to every window type we install.
Awning & Hopper Windows Pricing in Fresno
Most awning and hopper window replacements in Fresno run between $380 and $1,100 installed, per window, depending on size, frame material, glass package, and the condition of the existing opening. Here’s a breakdown of what affects the number:
- Window size. A small 24″ x 24″ hopper for a basement or utility room sits at the lower end. A wide 48″ x 36″ awning for a kitchen or living room climbs toward the upper end. The glass area drives the cost, plain and simple.
- Frame material. Vinyl is the most common and the most budget-friendly. Aluminum frames cost more but offer slimmer sightlines and often better longevity in direct sun. Our PGT and CGI aluminum awning windows hold up well on Fresno’s west-facing walls where the afternoon sun is brutal.
- Glass package. Low-E glass (a thin coating that reflects heat while letting light through) adds $40 to $120 per window depending on the coating and whether you choose dual-pane with argon fill. In Fresno, we recommend low-E on any window that gets direct afternoon exposure. Your AC bill will notice the difference within a season.
- Condition of the existing opening. If the rough opening is square and the flashing is intact, installation is straightforward. If we find dry rot at the sill or a frame that’s out of square, the repair adds to the total. The written price covers what we find when we open the wall up. The price is written before work starts. If we find rot during the job, we stop, explain what we found, and put the additional cost on paper before proceeding. No surprises at the door.
- Impact-rated or high-performance glass. If you want CGI impact-rated awning windows or tempered glass for safety glazing (required by code for windows near doors or below a certain height), expect to add $150 to $400 per window depending on size.
For a full-house replacement with a mix of awning, hopper, and fixed windows, Fresno homeowners typically spend $8,000 to $22,000 for 12 to 20 windows, depending on the mix of brands and glass packages. We write that number down before work begins, and it covers everything: windows, labor, flashing, trim, haul-away, and the 365-day guarantee. Call (559) 272-4716 and we’ll give you an exact figure for your house, free.
Awning vs. Hopper: Which One Belongs Where
Both windows seal tighter than sliders. The difference comes down to where the hinge sits and which way the sash swings, and Fresno’s climate makes that choice matter more than it does in, say, San Diego.
Awning windows hinge at the top and swing outward, so the open sash acts like a small roof over the opening. That’s why they work so well above a kitchen sink or over a garden window bed where you want to leave the window cracked during a spring shower. The bottom of the sash presses outward, which means the seal at the bottom actually tightens under gravity when the window is closed. That’s a mechanical advantage no slider can match.
Hopper windows hinge at the bottom and tilt inward, so the open sash directs air upward into the room. They’re the workhorse for basements, utility rooms, and any wall where the window sits low to the ground. In an older Fresno home with a basement that smells musty by August, a hopper window at each end of the basement gets cross-ventilation moving and costs far less than a mechanical ventilation system.
We also install Bay & Bow Windows and other combination units where the architecture calls for it. A fixed picture window with an awning window below it lets in light and ventilation without a mullion running through the middle of the view. In homes with a view of the Sierra Nevada from the second floor, that combination is the right answer. PGT and ViewLux both make these combination units as factory-assembled packages, which means the seals are done at the factory, not pieced together on site.
What Fresno’s Climate Means for Awning & Hopper Windows
Fresno gets over 30 days a year above 100 degrees, and summer overnight lows sometimes stay in the 80s. That thermal swing is hard on window frames and seals. Vinyl expands and contracts; aluminum conducts heat; wood dries and splits. Which is why we usually spec the frame material based on exposure. A west-facing wall in the Tower District gets hammered by the afternoon sun. An east-facing wall in Woodward Park gets the morning heat but then shade the rest of the day. The right window for one side of the house isn’t necessarily the right window for the other.
There’s also the matter of the Valley’s winter inversion layer. Fresno doesn’t freeze often, but when the temperature drops, it’s usually paired with damp, still air. Windows that seal tightly keep that dampness out of the wall cavity, which matters over the life of the house. The compression seals on a well-built awning or hopper window outperform the brush seals on a vinyl slider every time. That’s not a sales pitch; it’s a physical fact about how the two designs work.
One more thing worth knowing if you’re shopping: the 2019 Title 24 energy code in California requires new and replacement windows to meet specific U-factor and SHGC (Solar Heat Gain Coefficient) ratings depending on climate zone. Fresno is in climate zone 13, which means windows with a low SHGC are required on any wall that gets meaningful sun exposure. We spec low-E glass with a low solar heat gain coefficient on south- and west-facing installations as standard practice, because it’s what the code requires and what the house actually needs. You won’t have to ask for it; it’s already in the written price.
FAQs – Awning & Hopper Windows
How much does an awning window cost in Fresno?
An awning window replacement in Fresno typically costs $380 to $1,100 installed, depending on size, frame material, and glass package. A standard 36″ x 36″ vinyl awning window with dual-pane low-E glass usually lands in the $500 to $800 range. Larger aluminum units from brands like ViewLux or PGT run higher, especially with impact-rated or tempered glass. Call (559) 272-4716 for an exact quote on your opening, free of charge.
Are awning windows good for hot climates like Fresno’s?
Yes, awning windows perform well in hot climates because they seal tightly on all four sides and allow high ventilation placement that lets hot air escape. When placed high on a wall, an open awning window vents the hottest air near the ceiling. When closed, its compression seal stops conditioned air from leaking out, which matters when summer highs in Fresno routinely exceed 100 degrees.
Hopper window vs. awning window: which is cheaper?
Hopper windows are generally slightly cheaper than awning windows of the same size because the hardware is simpler. In Fresno, a hopper window typically runs $350 to $700 installed, while an awning window runs $380 to $1,100 installed. The real question is placement: hoppers belong low and inward-swinging, awnings belong high and outward-swinging. We’ll spec the right one for each opening and put the price on paper before work starts.
Can you install awning windows in a stucco house?
Yes, we install awning and hopper windows as part of our Window Installation services in stucco homes throughout Fresno regularly, including the many stucco homes built between the 1950s and 1980s in neighborhoods like Fig Garden and Sunnyside. The installation requires careful flashing and sealing where the stucco meets the window frame, and our crew does that on every job. If we find water damage behind the stucco, we’ll show you what we found and put the fix on paper before proceeding.
Do awning windows leak during Fresno’s winter rain?
Correctly installed awning windows do not leak during rain because the open sash angles downward like a small roof, directing water away from the opening. The compression seal around the entire frame also prevents water from getting in when the window is closed. If an awning window leaks, it’s almost always an installation problem or a failed seal, which is why our 365-Day Done Right Promise covers any installation failure for a full year at no charge.
Why Meridian Windows and Doors Fresno
We’re the windows-and-doors specialist within the Garrison Partners network. That means we operate locally, but we answer to a standard that’s been in place since 2009. Every job, on every house, from a single Casement Windows installation to a full-house awning window package in Woodward Park, gets the same treatment: a written price before work starts, a uniformed background-checked crew, and a 365-Day Done Right Promise in writing. If it fails within a year, we return at no charge. No fine print about labor exclusions. If the installation fails during that period, the second visit is free.
We carry eight manufacturer lines, including ViewLux, PGT, and CGI, so we’re not trying to fit your opening into whatever single brand we happen to stock. We spec the window the job needs. That’s the Garrison Standard, and it’s how we’ve done it since day one.
Elliot Vance leads the crew. He’s the person who shows up to measure, the one who writes the price down, and the one who answers when something goes sideways. When you call, you’re not calling a call center in another city. You’re calling a Fresno operation with a local owner who lives with the results of every install.
For awning and hopper windows in Fresno, the first step is a phone call. (559) 272-4716. A person answers. A time gets set. A price gets written down. And if we can’t make the window work the way you want it to, we’ll tell you that on the spot and recommend the window that will. That’s the straight story, which is the only story we know how to tell. You can also return to our home page for a broader look at everything we do.
Written by Elliot Vance, Owner at Meridian Windows and Doors Fresno, serving Fresno.
Six Reasons Homeowners Choose Meridian Windows and Doors Fresno
Laminated glass and reinforced frames hold up to wind-driven rain, hail and flying debris, so your openings stay sealed when the weather turns.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Tighter seals and insulated glass even out hot and cold rooms and stop the drafts at the frame.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.